Please scroll down to add to cart. Chassis Parts

Chassis Parts

Ball Bearings for Viper V1 & BSRT Scale Auto G3 Cars

Ball Bearings for Viper V1™ and  BSRT Scale Auto Chassis
 

These are quality stainless steel ball bearings.   They must be used with a ball bearing shaft armature such as a 'Spinner'.  They will not work on stock 6 ohm armature shafts.

Priced Per Pair of Bearings.

$14.99
Drill Chassis for Rear Axle .025 Retain Pins

Drilling of Viper Chassis for .025 Rear Axle Retaining Pins

Fee for drilling any Viper V1 chassis for .025 rear axle retaining pins.   Includes standard HCS AMG rear axle pins. 
 

$4.95
Gen-3 Diamond Endbell Brush Preseating Tool for Tomy & BSRT

 

Generation-3 Diamond Endbell Brush Pre-Seating Tool

     This somewhat unassuming tool is a true Pro Racer essential for running Viper V1, BSRT Scale Auto or Tomy Super G Plus cars.  It is used in conjunction with a brush-arm spreading tool to cut an arc in the motor brushes that approximates that of the armature commutator.  

The tool is used by first spreading the arms of the endbell with the endbell tool.  The diamond seater tool is then inserted into the endbell as an armature would.   The brush arms are then relaxed. About a dozen twists back and forth by hand will cut the arc.  Spread the arms back out and remove the tool.  Assemble the car and then break-in the motor at low voltage for few minutes. 

     NOTE:  not responsible for misuse. 

     DO  NOT use under power such as in a Dremel. 

    Practice on run-out endbells first.


 

 

$32.95
Hard Body Clip for Viper V1, BSRT G3, Tomy Super G Plus - Low Rider Style

 Low Rider Style Tomy Super G Plus Style Hard Body Clip

You've been asking for them - NOW you have them ! ! ! One each Low Rider style Tomy Super G Plus style hard body clip.  Brand New production run. 

These are the REAL DEAL engineered and injection molded parts like the discontinued Tomy SG+ clip. Clips work as well or better than the original. Allows fitting many Aurora Magna-Traction, Tomy, and Auto World X-Traction bodies onto Tomy Super G Plus, BSRT G3, and Viper V1 without the lexan posts.

This style clip allows a lower center of gravity with certain Tomy hard bodies.  Some bodies may need relief in certain areas for clearance.  But it is worth the extra handling performance.

Not cheap MarkerBot 3D printed globs of 'starter kit' parts that don't fit well and have to be whittled on to work.       

Bodies and chassis NOT included - for display only. 

 

 

 

$2.74
Hard Body Clip for Viper V1, BSRT G3, Tomy Super G Plus - Standard Style

 Standard Tomy Super G Plus Style Hard Body Clip

You've been asking for them - NOW you have them ! ! ! One each standard Tomy Super G Plus style hard body clip.  Brand New production run. 

These are the REAL DEAL engineered and injection molded parts like the discontinued Tomy SG+ clip. Clips work as well or better than the original. Allows fitting many Aurora Magna-Traction, Tomy, and Auto World X-Traction bodies onto Tomy Super G Plus, BSRT G3, and Viper V1 without the lexan posts.

Not cheap MarkerBot 3D printed globs of 'starter kit' parts that don't fit well and have to be whittled on to work.       

Bodies and chassis NOT included - for display only. 

 

 

 

$2.49
HCS AMG Brass Independent O-Ring Front End Set for Viper V1, BSRT G3-R, Tomy Cars

HCS AMG Brass Independent O-Ring Front End Set for Viper V1,  BSRT G3, Tomy SG+

CNC machined in the USA by RTHO brass front 'o-ring' hubs and axle sets.  These are designed to run in Viper V1 & BSRT G3-R for weighted or 'brass class' cars.  Other applications can be done.  Comes with 1 set of o-rings.  Different size o-rings can be fitted for fine tuning ride height.  Weight for complete set is 2 grams. 

You get one (1) complete axle set: Hubs, O-Rings, Axle.  Chassis NOT included - for display only.

 

 

$11.99
HCS AMG Pro-Trax 7T Tyco Style Delrin Pinion Gear

HC Slots AMG Pro-Trax™ 7T Delrin Pinion Gear

One each 7T Gear. Mates with Viper crown gears as well as Tomy, BSRT, and Tyco crown gears.  Designed after the Tyco 440 nylon pinion gear.  Delrin material offers better wear under tough conditions.

AMG - the Advanced Manufacturing Group of Harden Creek Slot Cars.

$1.65
HCS AMG Pro-Trax 7T Tyco Style Delrin Pinion Gears - 5 Each

HC Slots AMG Pro-Trax™ 7T Delrin Pinion Gears

Five each 7T Gears. Mates with Viper crown gears as well as Tomy, BSRT, and Tyco crown gears.  Designed after the Tyco 440 nylon pinion gear.  Delrin material offers better wear under tough conditions.

AMG - the Advanced Manufacturing Group of Harden Creek Slot Cars.

$7.49
HCS AMG Pro-Trax Independent Front Axle Set
HCS AMG Pro-Trax™ Independent Front End Set
 
Fits Viper V1™, BSRT G3-R and Tomy Super G Plus.  Produced from the best materials available. Comes with hubs and keepres, .340 to .345 front 'Donut' tires, drill-blank axle.  You may need a wheel press to push the keepers on straight or other proper tools.
 
Other applications may be done. Note that chassis such as Tyco 44x2 Wide-Pan are not recommended for this part since there is little to no source for donut tires large enough - generally about .400 +/-.  This part requires the racer/hobbyist to have a selection of sized donut tires to get the ride height proper for any specific chassis.  The tires supplied with these parts is only a starting point. 

AMG - the Advanced Manufacturing Group of Harden Creek Slot Cars.
 

$9.99
HCS AMG Rear Axle .025 Retain Pins - 10 each

HCS AMG .025 Rear Axle Retaining Pins

These are precision made 0.025 diameter pins.  Ideal for the Viper V1 chassis.  Can be adapted to other brands of chassis and HO slot cars.  

For Viper V1 chassis, start the hole with an 0.020 bit.  Then follow up with an 0.025 bit. 

10 pins each.  
 

$2.49
HCS AMG Stainless Steel Center Splined .059 Rear Axle

HCS AMG Stainless Steel Center Splined  Standard .059 Rear Axles

Priced for 1 each axle. These standard grade axles start with precision cut 1.115 length stainless steel stock.  Center splined to assure positive crown gear placement.  They are great replacements for any Tyco 440, Life Like, or other HO slot cars in standard applications.   
 

$1.49
HCS AMG Stainless Steel Center Splined .059 Rear Axles - Lot of 3 Each

HCS AMG Stainless Steel Center Splined  Standard .059 Rear Axles

Price for 3 axles. These standard grade axles start with precision cut 1.115 length stainless steel stock.  Center splined to assure positive crown gear placement.  They are great replacements for any Tyco 440, Life Like, or other HO slot cars in standard applications.   
 

$3.95
HO Slot Car Oiler - Viper Juice

HC Slots "Viper Juice" Slot Car Oiler

Just what you need on the work bench or track-side.  The best synthetic oil available. 

Refillable bottle design.

$4.99
Life Like "T" Car & Tomy AFX Mega-G+ Motor Pinion Gears - 5 Each

HCS AMG Motor Pinion Gears for Life Like "T"Cars

and Tomy AFX Mega-G+ Chassis

You get five each of gears.  These are the real deal new production run factory made parts.  Replaces motor pinion gears that have stripped out teeth.  Chassis for display only and not included.

Fits 1mm armature shafts.  Can be used on many "Mini Motor" gravity car applications. 

AMG - the Advanced Manufacturing Group of Harden Creek Slot Cars.

 

$6.95
Scale Engineering - HO Tire & Gear Press - 164-300

Scale Engineering - Tire & Gear Press

The Best HO Tire Press on the market offering many options for pressing Crown Gears and Tires.  The Tire Press saves you from damaging hubs and expensive silicone sponge tires.  Prevents excessive tire run out due to a poor and /or improper installation of  hubs and tires. 

$32.95
Scale Engineering - Pinion Tool - 164-320

Scale Engineering - Pinion Tool

The proper tool needed to hold pinion gears while pressing them onto the armature shafts.  Makes short work of installing and adjusting pinion gears.

$11.99
Tyco 440 & HP-7 Standard Factory Aluminum Guide Pins - 5 each

Tyco 440 & HP-7 Standard Factory Aluminum Guide Pins

Five each steel pins.  Specifically for Tyco cars.  Light weight design. 

$5.99
Tyco 440 & HP-7 Standard Factory Steel Guide Pins - 5 each

Tyco 440 & HP-7 Standard Factory Steel Guide Pins

Five each steel pins.  Specifically for Tyco cars

$4.49
Tyco 440 Standard Factory 25T Crown Gears - 3 each

Tyco 440 Standard Factory 25T Crown Gears

Three each Nylatron 25T Crown Gears.  Mate with Tyco pinion gears as well as Viper, Tomy, and BSRT pinion gears.  Gears can be utilized on other brands of HO slot cars when properly fitted.  Nylatron gears are not recommended for cars running Level 10 and higher magnets. 

$3.49
Tyco 440 Standard Factory 7T Pinion Gears - 5 each

Tyco 440 Standard Factory 7T Pinion Gear

Five each Nylatron 7T Pinion Gears.  Mate with Tyco crown gears as well as Viper, Tomy, and BSRT crown gears.  Tyco pinion gears have a long history of high quality.  Over the years, many HOPRA championship racers have used the Tyco pinion in there Pro Ceramic Super Stock cars

$12.95
Vibra-Tite VC-3 Threadmate - Non-hardening Threadlocker

Vibra-Tite VC-3 Threadmate 

     VC-3 is a non-hardening threadlocker that comes in handy for a variety of HO slot car applications.  Traditionally it has been used to keep Wizzard brush barrel screws from backing out during racing.  It also is good for lexan body pins to keep bodies secured during a race.

     Depending on how you apply it, you can use it as a 'glue' or a gap-filling compound.  If you mate parts while the VC-3 is freshly applied, it will dry after a point to 'cement' parts in  place.  But, parts can be pulled apart carefully when needed.  If you let the VC-3 flash off before mating parts, it will get stiff and not be tacky.  This can create a space-filling application such as lexan body pins for BSRT Scale Auto G3 body posts.

     VC-3 has been used with success for securing HC Slots 'clip-on' lexan bodies to their specific chassis application.  Most commonly this is the Frog body onto a Tyco 440x2 narrow chassis.

$6.95
Viper Double Flanged .250 OD Narrow Machined Delrin Rear Hubs - 2 sets

Viper Double Flanged .250 OD Machined Delrin Narrow Rear Hubs

Two pairs of  narrow style true Pro Quality precision CNC Machined Delrin Rear Hubs.  Will fit Tomy Super G Plus cars and Viper V1™ and BSRT G3 cars running full-width traction magnets and still be 'legal' over-all width. 

Works well on all brands of HO slot cars when properly installed with quality HO tire and press tools.  

(rear axle set-up in photo not included) 

$7.49
Viper Pro-Trax Tomy Mega-G Complete Rear Axle Set

Pro-Trax™ Complete Rear Axle Set for Tomy Mega-G Cars

You get one (1) complete rear axle set: Viper Single Flanged CNC cut hubs, 23T Crown Gear and T-Boss, Super Tires "A" for Mega-G.  Get your ride slammed for best handling!!   .

These are designed to run in Tomy Mega-G cars.  Other applications can be done with different size tires installed. 

Chassis NOT included - for display only.  Comes with Viper 7T pinion gear which works on Mega-G.  The pinion will not fit Mega-G +.     

$12.49
Viper Pro-Trax Tomy Mega-G+ Complete Rear Axle Set

Pro-Trax™ Complete Rear Axle Set for Tomy Mega-G+ Cars

You get one (1) complete rear axle set: Viper Single Flanged CNC cut hubs, 23T Crown Gear and T-Boss, Super Tires "A" for Mega-G+.  Get your ride slammed for best handling!!   .

These are designed to run in Tomy Mega-G+ cars.   

Chassis NOT included - for display only.  Comes with HCS AMG 7T pinion gear which works on the newer Mega-G+.  The pinion will not fit older Mega-G.     

$12.49
Viper Razor O-Ring Front End Set for Tyco 440 Wide-Pan Chassis

Viper O-Ring Front End Set for Tyco 440 Wide-Pan Chassis

You get one (1) complete axle set: Hubs, O-Rings, Axle.  Get your ride slammed for best handling!!   These are the real-deal CNC machined Delrin front 'o-ring' hubs and axle sets. 

These are designed to run in Tyco 440x2 & Mattel HPx2 Wide-Pan cars.  Other applications can be done with different size o-rings installed.  O-rings finish at .405 OD. For reference, factory Tyco / Mattel wide-pan fronts are .434 OD.

Sets shipped with hubs pressed on loose.  You may need press or other proper tools to get and exact fit to your specific car.  Chassis NOT included - for display only.

 

 

$4.49
Viper Razor O-Ring Front End Set for Tyco 440x2 Narrow and Tomy Mega-G, Mega-G+

Vper O-Ring Front End Set for Tyco 440x2 Narrow and Tomy Mega-G, Mega-G+

You get one (1) complete axle set: Hubs, O-Rings, Axle.  Get your ride slammed for best handling!!   These are the real-deal CNC machined Delrin front 'o-ring' hubs and axle sets.  .

These are designed to run in Tyco 440x2 Narrow and Tomy Mega-G and Mega-G Plus.  Other applications can be done with different size o-rings installed.  Comes with 2 sets of o-rings to get your car 'slammed'!!

Large O-rings finish at .360 OD. Smaller rings finish off at .354 OD.  

Sets shipped with hubs pressed on loose.  You may need press or other proper tools to get and exact fit to your specific car.  Chassis NOT included - for display only.

 

 

$4.49
Viper Razor O-Ring Front End Set for Viper V1, BSRT G3-R, Tomy Super G Plus

Vper O-Ring Front End Set for Viper V1,  BSRT G3, Tomy SG+

You get one (1) complete axle set: Hubs, O-Rings, Axle.  Get your ride slammed for best handling!!   These are the real-deal CNC machined Delrin front 'o-ring' hubs and axle sets.  .

These are designed to run in Viper V1, BSRT G3-R and Tomy Super G Plus.  Other applications can be done with different size o-rings installed.  Comes with 2 sets of o-rings to get your car 'slammed'!!

Large O-rings finish at .354 OD. Smaller rings finish off at .340 OD.  

Sets shipped with hubs pressed on loose.  You may need press or other proper tools to get and exact fit to your specific car.  Chassis NOT included - for display only.

 

 

$4.49
Viper Scale Racing - ''HardSpline'' Steel Center Splined .059 Rear Axle

Viper HardSpline™ Steel Center Splined  Premium .059 Rear Axles

Priced per each axle. These premium axles start with precision cut 1.15 length billet steel stock.  Center splined to assure positive crown gear placement. Axles are centerless ground, hardened, and nickel plated.  They are great replacements for any BSRT G-3, Tyco 440 car, or other HO slot cars.  
 

$2.95
Viper Scale Racing - ''HardSpline'' Steel Center Splined .059 Rear Axle - Lot of 5

Viper HardSpline™ Steel Center Splined  Premium .059 Rear Axles

Price for 5 axles. These premium axles start with precision cut 1.15 length billet steel stock.  Center splined to assure positive crown gear placement. Axles are centerless ground, hardened, and nickel plated.  They are great replacements for any BSRT G-3, Tyco 440 car, or other HO slot cars.  
 

$13.95
Viper Scale Racing 22T Crown Gear

Viper 22T Crown Gear

One each 22T Gear.  Injection molded from the best materials available.  Low profile design to save weight. Molded in tooth count markings.  Mate with Viper 7T pinion gears as well as Tomy, BSRT, and Tyco pinion gears.  (photo shows three, but priced individually)

$2.49
Viper Scale Racing 23T Crown Gear

Viper 23T Crown Gear

One each 23T Gear.  Injection molded from the best materials available.  Low profile design to save weight. Molded in tooth count markings.  Mate with Viper 7T pinion gears as well as Tomy, BSRT, and Tyco pinion gears.  (photo shows three, but priced individually)

$2.49
Viper Scale Racing 23T Mega-G & Mega-G+Crown Gear

Viper 23T Mega-G and Mega-G+ Crown Gear

One each 23T Gear. - made to fit Tomy Mega-G adn mega-G+.  Injection molded from the best materials available.  Low profile design to save weight. Molded in tooth count markings.  Mate with Viper 7T pinion gears as well as Tomy, BSRT, and Tyco pinion gears.  (photo shows three, but priced individually)

$2.49
Viper Scale Racing 7T Pinion Gear

Viper Scale Racing 7T Pinion Gear

One each 7T Gear. Mate with Viper crown gears as well as Tomy, BSRT, and Tyco crown gears.  (photo shows four, but priced individually)

$1.65
Viper Scale Racing 7T Pinion Gears (10 each)

Viper 7T Pinion Gears

Ten each 7T gears. Mate with Viper crown gears as well as Tomy, BSRT, and Tyco crown gears. 

$13.95
Viper Scale Racing Aluminum Body Posts for BSRT & Tomy A/FX Supe G Plus

Viper Aluminum Body Posts for BSRT & Tomy A/FX Super G Plus

You get 1 set of 4 posts. They are a direct screw-in fit for BSRT G3 and G3-R cars.  They can be fitted to Tomy Super G Plus and other brands of HO slot cars with properly located and drilled chassis.

Engineered and made from the best materials available.

Chassis in photos for example only, not included.  BSRT G3 is left rear, Tomy SG+ is right rear, Tyco 440 Narrow in front.

$4.49
Viper Scale Racing Extended Guide Pin for Viper V1, BSRT G3, and Tomy Cars

Viper Scale Racing Extended Guide Pin

1 Each. They fit most Aurora A/FX, Magna-Traction, G+, Tomy Turbo, SRT, Super G Plus, BSRT G3, Auto World X-Traction, and Viper V1™ cars.  

Viper Extended Pin is .180 deep.  The pin will work for Tomy factory track.  The pin will most likely be too long for other brands of plastic track as well as custom routed tracks. 

For reference, the standard Viper is .160 deep and BSRT extended pin is .210 deep. 

$2.95
Viper Scale Racing Gear Saver - ''T-Boss''

Viper Scale Racing Gear Saver - "T-Boss"

One each gear saver.  CNC machined from the best materials available.  Mate with Viper pinion and crown gears as well as Tomy, BSRT, and Tyco gears.  (photo shows three, but priced individually. Axle set for example, not included)

$1.95
Viper Scale Racing Low Friction Guide Pin for Viper V1, BSRT G3, and Tomy Cars

Viper Low Friction Guide Pin

They fit most Aurora A/FX, Magna-Traction, G+, Tomy Turbo, SRT, Super G Plus, BSRT G3, Auto World X-Traction, and Viper V1™ cars.  This guide pin features a reverse taper pin design that reduces friction in the slot and also allows the car to roll easier from side to side.

Viper Low Friction Pin is .180 deep.  Engineered and made from the best materials available.

 

$2.49
Viper Scale Racing Low Friction Guide Pins for Viper V1, BSRT G3, and Tomy Cars - 3 Each

Viper Low Friction Guide Pins

3 Each . They fit most Aurora A/FX, Magna-Traction, G+, Tomy Turbo, SRT, Super G Plus, BSRT G3, Auto World X-Traction, and Viper V1™ cars.  This guide pin features a reverse taper pin design that reduces friction in the slot and also allows the car to roll easier from side to side.

Viper Low Friction Pin is .180 deep.  Engineered and made from the best materials available.

 

$6.74
Viper Scale Racing Rear Armature Bushing

Viper Rear Armture Bushing

One each rear machined armature bushing.  For Viper V1, Tomy Super G Plus, and BSRT G3 cars.

 

$1.75
Viper Scale Racing V1 Pro Racing Flexible Chassis - HOPRA Approved

Viper Scale Racing V1 Flexible Chassis

One flexible chassis with timing bracket and magnet clip.  Chassis will accept parts from Tomy Super G Plus, Viper Scale Racing, BSRT, and others. Molded in lexan body posts. 

Flexible chassis designed for ceramic class and weighted class cars.  Level 4 may be indicated for some track applications. Not recommended for Level 10 or higher magnets. 

HOPRA Approved Part. 

The Next Generation of HO Racing™ is here.  Own a piece of it ;-)

$11.95
Viper Scale Racing V1 Pro Racing Medium Chassis - HOPRA Approved

Viper Scale Racing V1 Medium Chassis

One medium chassis with timing bracket, magnet clip, and endbell tension ring.  Designed to be the ultimate version of the Tomy Super G Plus.

Chassis will accept parts from Tomy Super G Plus, Viper Scale Racing, BSRT, and others. Molded in lexan body posts. 

Medium chassis designed for ceramic, Level 4, Level 10, and some polymer builds. 

Optional installation of the endbell tension ring allows racers to load the amount of tension between the endbell and the timing bracket.  Some guys like it loose, some like it tight... .

HOPRA Approved Part. 

The Next Generation of HO Racing™ is here.  Own a piece of it ;-)

$9.95
Viper Scale Racing V1 Pro Racing STIFF Chassis - HOPRA Approved

Viper Scale Racing V1 Stiff Chassis

One stiff chassis with timing bracket, and magnet clip.  Chassis will accept parts from Tomy Super G Plus, Viper Scale Racing, BSRT, and others. Molded in lexan body posts.

Stiff chassis great for any magnets above Level 10.  Perfect chassis for "Drop-In" neo car builds.  

Optional installation of the endbell tension ring allows racers to load the amount of tension between the endbell and the timing bracket.  Some guys like it loose, some like it tight... .

HOPRA Approved Part. 

The Next Generation of HO Racing™ is here.  Own a piece of it ;-)

$12.49
Viper Scale Racing V1 Pro Racing STIFF Chassis Kit - HOPRA Approved

Viper Scale Racing V1 Stiff Chassis Kit

One stiff chassis with timing bracket, magnet clip, endbell ring, rear axle retaining pins, guide pin, and independent front axle set.  Chassis will accept parts from Tomy Super G Plus, Viper Scale Racing, BSRT, and others. Molded in lexan body posts.

Stiff chassis great for any magnets above Level 10.  Perfect chassis for "Drop-In" neo car builds.  

Optional installation of the endbell tension ring allows racers to load the amount of tension between the endbell and the timing bracket. 

Steel rear axle retaining pins installed, Viper guide pin installed, Independent front axle set installed with .340 tires.  Front axle is a drill blank.

HOPRA Approved Part. 

The Next Generation of HO Racing™ is here.  Own a piece of it ;-)

$23.49
Viper Single Flanged .265 OD Narrow Machined Delrin Rear Hubs - 2 sets

Viper Single Flanged .265 OD Machined Delrin Narrow Rear Hubs

Two pairs of new narrow style CNC Machined Delrin Rear Hubs.  They solve lots of problems encountered with cheap factory hubs.  Will fit Viper V1™, Tomy Super G Plus cars and BSRT G3 cars running full-width traction magnets and still be 'legal' over-all width.  Works well on all brands of HO slot cars when properly installed with quality HO tire and press tools.

(axle set for display not included)

(axles  

$7.49
Wizzard High Performance 8T Pro Predator Pinion Gear

Wizzard High Performance 8T Pro Predator Pinion Gear

One each 8T Gear. Mate with Viper crown gears as well as Tomy, BSRT,Wizzard and Tyco crown gears. 

(photo shows four, but priced individually)

$1.95
Wizzard High Performance 8T Pro Predator Pinion Gear - 3 Each

Wizzard High Performance 8T Pro Predator Pinion Gears

Three each 8T Gear. Mate with Viper crown gears as well as Tomy, BSRT,Wizzard and Tyco crown gears. 

 

$5.49
Wizzard High Performance - Axle & Armature Shaft Spacers - .003

Wizzard HO - Axle Spacers - .003

These are precision made .003 thick bronze spacers.  Ideal for spacing armatures and rear axle gear mesh.  ID is .060 for standard .059 rear axles and armature shafts. 

8 each in the bags. 
 

$1.75
Wizzard High Performance - Axle & Armature Shaft Spacers - .005

Wizzard HO - Axle Spacers - .005

These are precision made .005 thick bronze spacers.  Ideal for spacing armatures and rear axle gear mesh.  ID is .060 for standard .059 rear axles and armature shafts. 

8 each in the bags. 
 

$1.75
Wizzard High Performance - Axle & Armature Shaft Spacers - .010

Wizzard HO - Axle Spacers - .010

These are precision made .010 thick bronze spacers.  Ideal for spacing armatures and rear axle gear mesh.  ID is .060 for standard .059 rear axles and armature shafts. 

8 each in the bags. 
 

$1.75
Wizzard High Performance - Axle & Armature Shaft Spacers - .015

Wizzard HO - Axle Spacers - .015

These are precision made .0105thick bronze spacers.  Ideal for spacing armatures and rear axle gear mesh.  ID is .060 for standard .059 rear axles and armature shafts. 

8 each in the bags. 
 

$1.75